JHM-1027x330x32
PROUDLY DESIGNED AND BUILT IN THE USA
**NOTE: As of 8/1/2012, all JHM Lightweight Rotors will now look like the picture below!!!***
Click to enlarge picture
Due to popular demand, all of our 2-piece, lightweight rotors will now come with black anodized rotor hats featuring Type 3, hard anodizing, the highest quality and hardest anodizing available for aluminum. This will make the rotor hats more resistant to fade and wear and will hide brake dust better. Due to popular, demand all lightweight rotor rings will also feature zinc plating. This high quality coating will slow the effects of corrosion and keep your rotor rings looking good through the winters.
IN STOCK AND READY TO SHIP!
-Rotor OD: Stock = 321mm(12.6"), JHM = 330mm(13") - .4" larger
-Rotor Thickness: Stock = 30mm(1.18"), JHM = 32mm(1.26") - thicker
-Rotor Weight: Stock = 21lbs(each), JHM = 19.5lbs(each) - 7% LIGHTER, 1.5lbs less each
-Rotor Cooling Air-gap: Stock = 11mm(.433"), JHM = 15.5mm(.610") - LARGER for better cooling
-Rotor Cooling Center Fin Design: Stock = Straight Fin, JHM = Airfoil - MORE EFFICIENT for better cooling
-Bolt pattern: - SAME (fits like an OEM rotor would)
- Go back one section if you need a hardware kit for adapting the calipers to your car (bolts, washers and nuts).
- Go back one section if you need need stainless brake lines that adapt these calipers to the B6/B7 A4.
We worked closely with a race brake manufacturer that supplies many NASCAR racers and a couple major brake kit companies. Due to their expertise we chose to have them build us the outer rings to our specs to fit the B6-B7 S4-A4 with a Cayenne caliper bolted on. 12 attachment points for durability and strength.
We CNC machine the Aluminum center hats in house based on their recommended materials and thicknesses for durability. 12 attachment points for durability and strength. We also engrave JHM in them in 3 locations equal from each other, it looks clean and doesn't jump out or look tacky.
NOTE: The C5 A6-S6 4.2l V8 spindles sometimes have excess material where the caliper mounts to the spindle at the upper mount point. This takes the caliper out of parallel to the rotor. Check for this by installing the caliper and rotor with no pads and checking that the outer pins are the same distance from the rotor (make sure you have the rotor flat and installed with 5 bolts). If the top pin is much closer or touching you need to shave down the upper mounting point until the caliper is parallel with the rotor. Also you will notice that the caliper is closer to both outer pins vs the outer pins, this is ok and as designed. This outward bias is there to give max clearance for the rotor from the spindle and for optimum performance. Unfortunately this is a mass produced cars and inconsistencies do happen from time to time in the manufacturing of a car. This is a quick fix and once the caliper is parallel the kit will install easily.
**NOTE: As of 8/1/2012, all JHM Lightweight Rotors will now look like the picture below!!!***
Click to enlarge picture
Due to popular demand, all of our 2-piece, lightweight rotors will now come with black anodized rotor hats featuring Type 3, hard anodizing, the highest quality and hardest anodizing available for aluminum. This will make the rotor hats more resistant to fade and wear and will hide brake dust better. Due to popular, demand all lightweight rotor rings will also feature zinc plating. This high quality coating will slow the effects of corrosion and keep your rotor rings looking good through the winters.
IN STOCK AND READY TO SHIP!
-Rotor OD: Stock = 321mm(12.6"), JHM = 330mm(13") - .4" larger
-Rotor Thickness: Stock = 30mm(1.18"), JHM = 32mm(1.26") - thicker
-Rotor Weight: Stock = 21lbs(each), JHM = 19.5lbs(each) - 7% LIGHTER, 1.5lbs less each
-Rotor Cooling Air-gap: Stock = 11mm(.433"), JHM = 15.5mm(.610") - LARGER for better cooling
-Rotor Cooling Center Fin Design: Stock = Straight Fin, JHM = Airfoil - MORE EFFICIENT for better cooling
-Bolt pattern: - SAME (fits like an OEM rotor would)
- Go back one section if you need a hardware kit for adapting the calipers to your car (bolts, washers and nuts).
- Go back one section if you need need stainless brake lines that adapt these calipers to the B6/B7 A4.
We worked closely with a race brake manufacturer that supplies many NASCAR racers and a couple major brake kit companies. Due to their expertise we chose to have them build us the outer rings to our specs to fit the B6-B7 S4-A4 with a Cayenne caliper bolted on. 12 attachment points for durability and strength.
We CNC machine the Aluminum center hats in house based on their recommended materials and thicknesses for durability. 12 attachment points for durability and strength. We also engrave JHM in them in 3 locations equal from each other, it looks clean and doesn't jump out or look tacky.
NOTE: The C5 A6-S6 4.2l V8 spindles sometimes have excess material where the caliper mounts to the spindle at the upper mount point. This takes the caliper out of parallel to the rotor. Check for this by installing the caliper and rotor with no pads and checking that the outer pins are the same distance from the rotor (make sure you have the rotor flat and installed with 5 bolts). If the top pin is much closer or touching you need to shave down the upper mounting point until the caliper is parallel with the rotor. Also you will notice that the caliper is closer to both outer pins vs the outer pins, this is ok and as designed. This outward bias is there to give max clearance for the rotor from the spindle and for optimum performance. Unfortunately this is a mass produced cars and inconsistencies do happen from time to time in the manufacturing of a car. This is a quick fix and once the caliper is parallel the kit will install easily.
⚠️CALIFORNIA WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
Product title
Vendor
$19.99 CAD | $24.99 CAD
Product title
Vendor
$19.99 CAD | $24.99 CAD
Product title
Vendor
$19.99 CAD | $24.99 CAD
Product title
Vendor